FRED J WAHL

LATEST ACTIVITY

• Posted in thread: Thinking about buying a C9 or 45ACP pistol on 02-28-2013 at 04:52 AM
  Michael1953, you can't go wrong with any of Hi Point's products, I have NEVER seen a published
  magazine review that EVER bad-mouthed the Hi Points, and they have been written up by "Gun
  Tests" magazin...

• Posted in thread: roll pin for slide on 02-28-2013 at 04:40 AM
  USMC VET, FIRST, THANK YOU FOR YOUR SERVICE! What a lot of guys seem to have done with our Hi
  Points, is to just grind a small bit of the Zamac metal away on the slide, only on the side
  where you inse...

• Posted in thread: G&A Shooting Times .45 ACP and .40 S&W Hi-Point Review! on 12-20-2012 at 10:18 PM
  Hey, Honest Abe and all, Just a "heads up" on the latest Hi Point C-9 magzine article/review in
  the current latest issue of "Handguns" Magazine, (Feb./March issue). It's by the same dude who
  did the e...

• Posted in thread: The BRASS Exchange on 12-12-2012 at 04:55 AM
  I have a batch of assorted brass I'd like to swap for .45 ACP commercial, (not Milsurp), or .38
  Spl. I have some .45 GAP, .357 Sig, and lots of 9MM, will trade two 9mm once-fired cases for
  one .45 ACP...

• Posted in thread: Use brass shells in your C9 on 12-11-2012 at 12:38 AM
  Hi All, Regarding Tula Steel cased ammo, I for one won't buy any more of it! In all three of my
  H-P 9mms, (two C-9's and a Comp), the bullet seem to "keyhole" badly, at my usual 25 yards
  distance! Abo...

• Posted in thread: Howdy! Just got a C9! on 12-11-2012 at 12:15 AM
  Hey, D_Saum! Welcome to the Hi Point Forum, and congrats on making the right decision, as far
  as your new C-9 is concerned! The prices seem to vary a lot on them, depending on where you are
  in the cou...

• Posted in thread: c9 trigger pull weight on 12-10-2012 at 11:55 PM
  I just read a Magazine article on the C-9 where the tester tried the trigger npull three tines,
  on a new gun, with a trigger pull guage,and it was 12 lbs. each time. This will no doubt
  "lighten up" af...

• Posted in thread: Trigger pinching on 12-01-2012 at 06:11 AM
  Hey, Wheeljack,Yeah, I did some altering to my 2 C-9's, and my Veteran bud's C-9, took a few
  minutes with my Dremel tool with a grind stone mounted in it. I ground the raised ridges off of
  the trigger...

• Posted in thread: Hi Point .45 - A war machine on 12-01-2012 at 06:00 AM
  Thanks for the reply!I don't mean to "Highjack" the thread, but I have found the same thing in
  regards to using Bullseye powder in all my .45's, that powder in it's original formula has been
  around fo...

• Posted in thread: Hi Point .45 - A war machine on 11-30-2012 at 04:36 AM
  Duster066, I've been doing a lot of handloading on all 9 of my Hi Points, and have tried using
  lead bullets as much as possible-- accuracy has been so-so, with the .40 S&W and my C-9's, and
  I've been ...