Hi-Point Firearms Forums banner
1 - 20 of 20 Posts
G

·
Discussion Starter · #1 ·
Just found HPFF,sweet! Love my 40carbine. Want to buy a 9mm carbine and get a ATI stock. Was wondering if its as easy as they say and were do I find hicap mag.
 
G

·
Discussion Starter · #2 ·
I wish I could help you, I don't have an ATI stock "yet", but I too wonder how hard they are to install and if they were lighter than the stock one.
 

·
Registered
Joined
·
1,464 Posts
It's not rocket surgery, it's swapping a stock. It's no more difficult than properly cleaning your weapon. aka... basic maintenance

The only thing that can be a pita are the receiver cover bolts, but that's nothing you and a dremel can't fix.
 
G

·
Discussion Starter · #5 ·
Iam goin put one of those on my new 995 ..It sure improves the UGLY STICK LOOK.. 69.oo @ midway :cry2:
 
G

·
Discussion Starter · #6 ·
I have a 4095 and don't mind how bad its looks, but I thinks the ATI really looks sweet. Knowing my luck with these kind of projects I'm glad this form is here.
 

·
Registered
Joined
·
4,752 Posts
please check the prices at www.milsurpstuff.com after shipping costs are added and such... They had the best price after shipping before i scored a used one from a board member.
 

·
Registered
Joined
·
99 Posts
Thanks I ordered one today, haven't even bought the 9 carbine yet.
The second pats the real clincher. For most people they cant even find them in their area. I was lucky and found one at a gun show a couple weeks after i turned 18 for next to nothing. But from what i hear they're becoming few and far between for a reasonable price.
 

·
Premium Member
Joined
·
345 Posts
please check the prices at www.milsurpstuff.com after shipping costs are added and such... They had the best price after shipping before i scored a used one from a board member.
Tell Benny you're a member and you'll get a discount. I ordered mine and he sent it a.s.a.p. Highly recommended.
 

·
Si vis pacem para bellum
Joined
·
548 Posts
I installed a ATI stock a couple of weeks ago along with a barrel shoud. I think I had a couple of hours in it total. the rear hex bolt on the action mount was out of line but I used a drill to ream the hole very carefully. I love the looks and feel.
 

·
Registered
Joined
·
51 Posts
Just came from outdoorbunker.com where they have ATI HP stocks for $46.49 with shipping at about $8. Orders over $100 qualify for free "7 day ground" shipping.
 
G

·
Discussion Starter · #15 ·
Well ATI stock installed!!! Those hex shroud bolts are a pain in the neck! Thank God for the dremmel tool. Action seem to jam just playin with it, but the gun has never been fired. I just talked to a gun show dealer who tells me he has 15rd mags that don't jam. I'm pickin up 2 tommorow. Shootin sunday.
 

·
Registered
Joined
·
799 Posts
Im going to try and save you from the 15rnders they are junk and many here will testify to that stick with the factory 10's hope this gets to you in time to save you some :'(
 

·
Registered
Joined
·
38 Posts
i have never disassembled or modified a firearm, and the ATI swap was extremely easy for me. took me a total of an hour to install my 995 in it.
 

·
Registered
Joined
·
15 Posts
I ordered an ATI stock for my 995 from milsurpstuff.com. The price was great, the shipping was lightning fast (even though I ordered it during the Holidays!). From start to finish the install took me 2½ hours, three beers and four expletives. One da**receiver bolt--the front one--caused me almost all of the heartache. Then, I get it all together and remove the Red Dot scope that came on the weapon to install the iron sights. BIG MISTAKE! Did not know that there were screw plates under the shroud that the screws bit into. These two plates dropped down and rattled into the receiver. Sackajewea! Back off came the receiver with the devil front bolt. got the screw plates out, installed the iron sights and spent another 20 minutes putting the receiver shroud back on again, futzing with that danged front bolt! FINALLY got it all together and it does look 150% better, IMHO.

Hint that worked for me (hopefully this didn't cause any issues): I did not button down the barrel, or slip in the C-clip before I put my receiver bolts in. After the bolts were in I then buttoned down the barrel and installed the C-clip. That little bit of extra schlop made the installation of the devil bolt a little bit easier for me.

Definitely order from milsurpstuff.com (PM him for a small discount) and do not rush the install.
 
1 - 20 of 20 Posts
Top